KLT900 online turbidity meter turbidity sensor water quality
stainless steel probe Lightning proof
Production Introduction
Outlines that the TSS turbidity/suspended matter concentration
meter is an on-line analytical instrument designed for measuring
turbidity or suspended matter in municipal sewage or industrial
wastewater treatment.The TSS turbidity/suspended matter
concentration meter consists of a transmitter and a sensor.The
sensor can be easily installed in a pool or in a natural water
body.The TSS turbidity/suspended matter concentration meter
automatically compensates for the interference caused by
pollution.Bidirectional digital communication between the
transducer and the transducer prevents signal attenuation and
allows greater distance between the transducer and the transmitter.
Measuring principle
TSS turbidity/suspended matter concentration meter work principle
as shown in figure 1-1, sensor transmitter to send the red outside
light in transit after being measured the absorption and scattering
of content, part of the scattering light to 135°direction of
detector, part of the scattering light detector to 90°direction.The
light intensity in the direction of 135°and 90°is related to the
turbidity of the measured sewage to a certain extent, and the
TURBidity of TSS is precisely based on this principle for
measurement.
Turbidity meter size structure diagram
host size
sensor size
Turbidity meter technical parameters
| Performance | value |
| System | Menu-driven software, with multi-point calibration function and
binding programming, can set the measurement range, relay and
current output; |
| Supply | AC220V (min85V- max265V) 50/60Hz |
| Maximum power consumed | 15 VA |
| Fuse | 2A /220VAC |
| Range | 0~4000 NTU |
| Measurement Unit | NTU and mg/L are available. |
| Resolution Rate | 0.1NTU |
| Accuracy | 2% of the measured value, within 10NTU the error is not greater
than 1NTU. |
| Display | The display screen is 192 × 64 pixels, which can display turbidity
measurement value, current time, historical trend line, etc. |
| Principle | infrared light scattering 90° and 135° |
| Output | 1 channel 4~20mA current signal isolation output, maximum load 750
ohms; 1-channel RS232 and 1-channel RS485 digital output
(optional); 3 alarm signal relays, capacity 220 VAC/ 2 A, output
can be set by the user; |
| Host:Material | ABS+PC |
| Host:Protection Level | IP65 |
| Sensor Material | 316L stainless steel |
| Cable Length | Dedicated shield cable, standard 10 meters (extendable) |
| Operating Temperature | 0-50℃ |
| Pressure | 0.6MPa |
| Calibrate | It has been calibrated before delivery and no calibration is needed
on site |
Ordering Information Selection Table
| Ordering Information Selection Table |
| KXTX00 | PH/ORP analyzer |
| Power supply | DC24V |
| AC220V |
| Cable length | 5m |
| 10m |
| 15m |
| 20m |
| Temperature compensation | Sensor without temperature compensation |
| Sensor with temperature compensation |
| Signal output | Only 4-20mA |
| Only 485 |
| Also with 4-20mA , 485 signal output |
| Special custom signal |
| KLT500-DC24V--5m-Sensor without temperature compensation-Only 485 | Low Turbidity host, with DC 24V adapter, cable between host and
sensor,The cable length is 5 meters, the sensor is equipped without
temperature compensation, and is only 485 communication. |
Contact us
Website: www.kacise.com
Phone: +86-17719566736
Email: sales@kacise.com
Location: Tangyan South Road, High-tech Zone, Xi'an City, Shaanxi
Province, China
Abbreviations table
NTU
The unit of turbidity is "degree", which is equivalent to the
degree of turbidity produced by 1L water containing 1mg SiO2 (or
white clay, diatomite), which is 1 degree, or Jackson.Turbidity
unit is JTU, 1JTU=1mg/L white clay suspension.
The turbidity shown by modern instruments is the unit of scattering
turbidity NTU, also known as TU.1NTU= 1JTU.
Recently, it is considered internationally that the standard of
turbidity prepared with ullotropin-hydrazine sulfate has good
reproducibility and is chosen as the uniform standard of
FTU.1FTU=1JTU.
