KUS3000 M30-Type1 Ultrasonic Level Meter

1.Feature

• High repeatability
• compact case
• non-contact detection;
• Not affected by object color and transparency; not affected by external environmental conditions, reliable solution;
• Works well in extreme conditions; able to be used in dark environments; low current consumption;
• The built-in anti-jamming smart chip has a fast frequency response, and the brass nickel-plated shell is flame-retardant, waterproof and oil-proof;
• The LED working indicator light is easy to use.
• The ABS induction probe and connectors are seamlessly connected with the equipment in various ways.

2. Dimensional structure

The unit is mm.

3. Electrical interface

Note: This product has two cable specifications, and the cable wiring instructions of the two specifications are as follows:

The default cable mix is based on the specifications received by the customer

4. Technical parameter

Indicator light

Electrical parameters

IOT-spectric models

Output

Temperature Requirements

Mechanical part description

Note: When the M18 product and M30 product have 4-20mA analog output, the meter connection method is different from that of the 550,600 product. Since the output terminal of the M18 and M30 products is powered by VDD, as shown in Figure 1, the meter should be connected to the power supply port. Between the output terminal and the output terminal, the connection instruction diagram is shown in Figure 2:

Figure 1 Output power supply circuit diagram

Figure 2 Schematic diagram of connection method

5. Sensor function description

Switch point and advance interval setting and adjustment of switch output and analog output products

Switch value and analog output can be set using the adjustment terminal, specifically, there are 8 working modes that can be set.

The specific setting method of each type of bean flour is the following steps.

In the first step, the user selects a distance set by himself, or puts the sensor into a lost wave state.

The second part, connect the calibration terminal to the power supply or GND, keep it connected until the yellow light flashes (if the wave is lost, the red light flashes).

In the third step, the user selects the second distance set by himself, or lets the sensor enter the lost wave state.

The fourth step, connect the calibration terminal to GND or power supply (the state is different from the second step), keep it connected until the yellow light flashes (if the wave is lost, the red light flashes).

There are 8 working modes of switch output

1. Window normally open mode (analog output products are in positive linear working mode or distance measurement mode).

2. Window normally closed mode (analog output product is in negative linear working mode or liquid level measurement mode).

3. Single point normally open mode.

4. Single point normally closed mode.

5. Single-point normally open mode with large hysteresis interval.

6. Single point normally closed with large hysteresis interval mode.

7. Whether to detect the normally open mode.

8. Whether to detect normally closed mode.

Description of RS485 output model products.

There are 3 working modes,

1: Automatic measurement mode, the sensor continuously measures the liquid level and distance, and the user can read the measurement results through the 485 interface at any time.

2: If the user does not initiate a 485 communication, the sensor will initiate a measurement and report the result.

3: Sleep mode, the product enters sleep mode, the user first wakes up the sensor through the 485 interface, and then initiates a measurement and obtains the result before the sensor sleeps again.

6. Installation conditions

When installing, pay attention to protect the surface of the sensor to avoid injury. If you work in an environment with heavy volatile gas or dust and heavy condensation, you need to clean the surface of the sensor regularly to avoid sensitivity reduction or failure to work. The installation thread should not be over-tightened, which will cause the sensor to be pressurized and not work properly.

7. Order information

Xi'an Kacise Optronics Co.,Ltd. is a professional manufacturer of  measuring instruments , located in China xi’an City. Since 2008, Xi'an Kacise focused on the development and production of pressure, level and flow measuring instruments .

We have been specializing in manufacturing pressure, level and flow measuring instruments and related products for 10 years. Based on experienced technical and management personnel, through efforts of our entire staff, we have become a professional measuring instrument manufacturer and solution provider. And we are continuously trying to improve product quality.

Xi'an Kacise is qualified with ISO 9001-2008, GJB 9001B-2009, CE, intrinsic safety explosion-proof and isolated safety explosion-proof certificates, etc. which ensure that our products comply with international standards.

Kacise sensors have already been exported to America, Spain, Australia, Chile and 20 other countries and regions, and received many favorable feedbacks. Our overseas distributers are also increasing. We regard “reasonable prices, efficient production time and good after-sales service” as our tenet, and hope to cooperate with more customers for mutual development.

Our goal is simple: to sell the best products at the best prices, and provides industry-leading customer service. We personally get to know each of our customers, and we know how to discover the most valuable part of our business , to help others achieve their goals.